Warning Icon
This product was discontinued on: March 27, 2020

For other alternatives, please contact us for more information.

1 Replacement products available
  • RRV4-65D-R6
    12-port sector antenna, 4x 694–960 and 8x 1695–2690 MHz, 65° HPBW, 6x RET. Antenna rear wind loading 880N @ 150km/h

CCV4PX310.11R-C3

12-port sector antenna, 4x 790–960 and 8x 1695–2690 MHz, 65° HPBW, 6x RET with manual override. Bands cascaded SRET.
Specifications
Finish making your selections or clear them to view relevant specifications.
Features and Benefits
  • Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual override on all arrays
  • All Internal RET actuators are connected in “Cascaded SRET” configuration
  • Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector
Specifications

General Specifications

Antenna Type Sector
Polarization ±45°
Band Multiband
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN | Outdoor usage
Radome Material Fiberglass, UV resistant
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 8
RF Connector Quantity, low band 4
RF Connector Quantity, total 12

Remote Electrical Tilt (RET) Information, General

RET Interface 8-pin DIN Male | 8-pin DIN Female
RET Interface, quantity 1 male | 1 female

Dimensions

Width 498 mm | 19.606 in
Length 2720 mm | 107.087 in
Depth 197 mm | 7.756 in

Array Layout

Click on image to enlarge.

Port Configuration

Click on image to enlarge.
Click on image to enlarge.

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 790 – 960 MHz | 1695 – 2690 MHz

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)
Power Consumption, idle state, maximum 2 W
Power Consumption, normal conditions, maximum 13 W
Input Voltage 10–30 Vdc
Internal RET Low band (2) | High band (4)

Electrical Specifications

Frequency Band, MHz 790–862 880–960 1695–1880 1850–1990 1920–2180 2300–2500 2500–2690
Gain, dBi 15.8 16.4 16.7 16.8 17.4 18.1 18.1
Beamwidth, Horizontal, degrees 73 62 63 66 67 62 64
Beamwidth, Vertical, degrees 8.9 8.1 7.6 7 6.6 5.5 5.2
Beam Tilt, degrees 0–10 0–10 0–10 0–10 0–10 0–10 0–10
USLS (First Lobe), dB 18 18 18 18 18 18 18
Null Fill, dB -22 -22 -22 -22 -22 -22 -22
Front-to-Back Ratio at 180°, dB 35 34 33 38 39 39 41
Isolation, Cross Polarization, dB 28 28 28 28 28 28 28
Isolation, Inter-band, dB 28 28 28 28 28 28 28
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum, watts 300 300 250 250 250 250 250

Electrical Specifications, BASTA

Frequency Band, MHz 790–862 880–960 1695–1880 1850–1990 1920–2180 2300–2500 2500–2690
Gain by all Beam Tilts, average, dBi 15.5 16.2 16.4 16.4 16.9 17.8 17.8
Gain by all Beam Tilts Tolerance, dB ±0.5 ±0.3 ±0.4 ±0.5 ±0.8 ±0.4 ±0.4
Gain by Beam Tilt, average, dBi 0 ° | 15.5
5 ° | 15.5
10 ° | 15.6
0 ° | 16.2
5 ° | 16.2
10 ° | 16.1
0 ° | 16.3
5 ° | 16.4
10 ° | 16.4
0 ° | 16.4
5 ° | 16.4
10 ° | 16.4
0 ° | 16.9
5 ° | 16.9
10 ° | 16.9
0 ° | 17.9
5 ° | 17.9
10 ° | 17.6
0 ° | 17.7
5 ° | 17.8
10 ° | 17.7
Beamwidth, Horizontal Tolerance, degrees ±5.7 ±4.7 ±3.4 ±7.3 ±4.6 ±3.7 ±3.7
Beamwidth, Vertical Tolerance, degrees ±0.4 ±0.3 ±0.5 ±0.3 ±0.5 ±0.3 ±0.2
USLS, beampeak to 20° above beampeak, dB 18 18 18 18 18 18 18
Front-to-Back Total Power at 180° ± 30°, dB 23 24 26 30 30 32 32
CPR at Boresight, dB 19 18 20 20 19 17 18
CPR at Sector, dB 11 9 9 10 11 11 12

Material Specifications

Radiator Material Low loss circuit board
Reflector Material Aluminum

Mechanical Specifications

Wind Loading at Velocity, frontal 1,085.0 N @ 150 km/h | 243.9 lbf @ 150 km/h
Wind Loading at Velocity, lateral 85.4 lbf @ 150 km/h | 380.0 N @ 150 km/h
Wind Loading at Velocity, maximum 315.6 lbf @ 150 km/h | 1,404.0 N @ 150 km/h
Wind Speed, maximum 200 km/h | 124.274 mph

Packaging and Weights

Width, packed 565 mm | 22.244 in
Depth, packed 312 mm | 12.283 in
Length, packed 2906 mm | 114.41 in
Net Weight, without mounting kit 54 kg | 119.049 lb
Weight, gross 78.8 kg | 173.724 lb

Regulatory Compliance/Certifications

Agency Classification
CE Compliant with the relevant CE product directives
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system

General Specifications

Antenna Type Sector
Polarization ±45°
Band Multiband
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN | Outdoor usage
Radome Material Fiberglass, UV resistant
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 8
RF Connector Quantity, low band 4
RF Connector Quantity, total 12

Remote Electrical Tilt (RET) Information, General

RET Interface 8-pin DIN Male | 8-pin DIN Female
RET Interface, quantity 1 male | 1 female

Dimensions

Width 498 mm | 19.606 in
Length 2720 mm | 107.087 in
Depth 197 mm | 7.756 in

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 790 – 960 MHz | 1695 – 2690 MHz

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)
Power Consumption, idle state, maximum 2 W
Power Consumption, normal conditions, maximum 13 W
Input Voltage 10–30 Vdc
Internal RET Low band (2) | High band (4)

Electrical Specifications

Frequency Band, MHz 790–862 880–960 1695–1880 1850–1990 1920–2180 2300–2500 2500–2690
Gain, dBi 15.8 16.4 16.7 16.8 17.4 18.1 18.1
Beamwidth, Horizontal, degrees 73 62 63 66 67 62 64
Beamwidth, Vertical, degrees 8.9 8.1 7.6 7 6.6 5.5 5.2
Beam Tilt, degrees 0–10 0–10 0–10 0–10 0–10 0–10 0–10
USLS (First Lobe), dB 18 18 18 18 18 18 18
Null Fill, dB -22 -22 -22 -22 -22 -22 -22
Front-to-Back Ratio at 180°, dB 35 34 33 38 39 39 41
Isolation, Cross Polarization, dB 28 28 28 28 28 28 28
Isolation, Inter-band, dB 28 28 28 28 28 28 28
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port, maximum, watts 300 300 250 250 250 250 250

Electrical Specifications, BASTA

Frequency Band, MHz 790–862 880–960 1695–1880 1850–1990 1920–2180 2300–2500 2500–2690
Gain by all Beam Tilts, average, dBi 15.5 16.2 16.4 16.4 16.9 17.8 17.8
Gain by all Beam Tilts Tolerance, dB ±0.5 ±0.3 ±0.4 ±0.5 ±0.8 ±0.4 ±0.4
Gain by Beam Tilt, average, dBi 0 ° | 15.5; 5 ° | 15.5; 10 ° | 15.6 0 ° | 16.2; 5 ° | 16.2; 10 ° | 16.1 0 ° | 16.3; 5 ° | 16.4; 10 ° | 16.4 0 ° | 16.4; 5 ° | 16.4; 10 ° | 16.4 0 ° | 16.9; 5 ° | 16.9; 10 ° | 16.9 0 ° | 17.9; 5 ° | 17.9; 10 ° | 17.6 0 ° | 17.7; 5 ° | 17.8; 10 ° | 17.7
Beamwidth, Horizontal Tolerance, degrees ±5.7 ±4.7 ±3.4 ±7.3 ±4.6 ±3.7 ±3.7
Beamwidth, Vertical Tolerance, degrees ±0.4 ±0.3 ±0.5 ±0.3 ±0.5 ±0.3 ±0.2
USLS, beampeak to 20° above beampeak, dB 18 18 18 18 18 18 18
Front-to-Back Total Power at 180° ± 30°, dB 23 24 26 30 30 32 32
CPR at Boresight, dB 19 18 20 20 19 17 18
CPR at Sector, dB 11 9 9 10 11 11 12

Material Specifications

Radiator Material Low loss circuit board
Reflector Material Aluminum

Mechanical Specifications

Wind Loading at Velocity, frontal 1,085.0 N @ 150 km/h | 243.9 lbf @ 150 km/h
Wind Loading at Velocity, lateral 85.4 lbf @ 150 km/h | 380.0 N @ 150 km/h
Wind Loading at Velocity, maximum 315.6 lbf @ 150 km/h | 1,404.0 N @ 150 km/h
Wind Speed, maximum 200 km/h | 124.274 mph

Packaging and Weights

Width, packed 565 mm | 22.244 in
Depth, packed 312 mm | 12.283 in
Length, packed 2906 mm | 114.41 in
Net Weight, without mounting kit 54 kg | 119.049 lb
Weight, gross 78.8 kg | 173.724 lb
Click on image to enlarge.
Click on image to enlarge.
Click on image to enlarge.

Regulatory Compliance/Certifications

Agency Classification
CE Compliant with the relevant CE product directives
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
Documentation & Downloads

Assembly Drawing

Environment Health and Safety

Installation Instruction

Product Information

Product Specification

Product Specification (Comprehensive)

Warranty

Other Ways to Browse

Browse by Application

Browse by Application